Electronic brake control, Components of the brake control, De b a
Advertising
Tekonsha ®, the Tekonsha ® logo, and Tekonsha ® graphics are the servicemarks, trademarks, or registered trademarks owned by Horizon Global Corporation. All other servicemarks, and trademarks are the property of their respective owner. Electronic brake control, Components of the brake control, De b a. Read online or download PDF. Tekonsha Voyager User Manual Manuals Directory ManualsDir.com - online.
Electronic Brake Control
For 2, 4, 6* and 8* brake applications
Components of the Brake Control
A. Power Knob B.
Manual Slide Knob
C. Bracket Mounting Holes D.
Bi-Colored Light
E.
Level Knob
Important Facts to Remember
1.
Do not mount or activate RF generating items (cell phones, two way radios) near (less than 12') the Brake Control.
2.
CAUTION Reversing the connection to a break-
away battery on the trailer will destroy the Brake Control.
3.
CAUTION Disconnect trailer plug from the tow
vehicle prior to testing a breakaway switch or you may destroy the Brake Control.
4.
The light is: • GREEN when trailer is connected. • RED when brake pedal or manual is
activated and trailer is connected.
5.
The GREEN light draws 5 milliamperes of current from tow vehicle. It would take over 10,000 hours to drain the tow vehicle battery.
6.
WARNING The level adjustment is CRITICAL.
The level adjustment determines whether automatic braking response is delayed or aggressive.
7.
This brake control is activated by inertia. It senses deceleration and generates an output that reflects the inertia sensed. In a stationary state, the brake control will not apply the trailer brakes unless the Manual Slide Knob is actuated.
8.
WARNING The Gross Combined Weight
Rating (GCWR) must never exceed the vehicle manufacturers recommendation.
9.
This control specfically designed for use with electric trailer brakes.
10. For Technical Assistance and Warranty Information
call: 1-888-785-5832 or www.tekonsha.com
Installation Guide
WARNING The Brake Control must be mount-
ed from -20 degrees nose down to 70 degrees nose up. (See Below.) Failure to install brake control within these constraints may cause your control to become inoperable.
Traditional Bracket Mount
A. Mounting Bracket B.
#6 x 3/8” Screws
1.
Hp laserjet 1320 manual download windows 10. For a USB cable that is commonly used for printers, make sure that it is not connected to a PC / Laptop device or your smartphone.3. Turn on your printer first.2. The software that you have downloaded on this website page is immediately opened4.
CAUTION Drilling or use of longer screws
may damage unit.
2.
Securely mount bracket to a solid surface.
3.
Insert supplied #6 x 3/8” screws on each side into the mounting holes.
4.
Adjust control to desired position and tighten screws until snug.
READ THIS FIRST:
Read and follow all instructions carefully before installing or operating the Brake Control. Keep these instructions with the Brake Control for future reference.
After the brake control has been securely mounted the level adjustment must be set.
1.
Samsung gear 3 frontier user manual. SummaryCritic RatingN/AN/AN/A3.5 /5 User RatingN/AN/AN/A5 /5 featuresVoice Control, Fitness TrackingWaterproof, Fitness TrackingWaterproof, Fitness TrackingWaterproof, Fitness Trackingbattery340 mAh battery capacityUpto 4 Days battery life (380 mAh)Upto 4 Days battery life (380 mAh)300 mAh battery capacitydesignCurved Dial DesignCircular, Flat Dial DesignCircular, Flat Dial DesignCircular Dial Designdisplay1.4 Inch (3.56 cm) Super AMOLED Display1.3 Inch (3.3 cm) Super AMOLED Display1.3 Inch (3.3 cm) Super AMOLED Display1.2 Inch (3.05 cm) AMOLED Display.
Connect trailer to tow vehicle, Bi-Colored Light should glow GREEN.
2.
Set power knob to maximum by fully rotating clockwise.
3.
Depress tow vehicle’s brake pedal and hold.
4.
Rotate the Level Knob counter-clockwise (towards the back of the control) until the Bi-Colored Light starts to change colors from GREEN to RED.
5.
Carefully rotate the Level Knob clockwise (towards the front of the control) until a shade of ORANGE is visible. Bi-Colored Light should show: • DIM ORANGE for a typical setting. • BRIGHT ORANGE for an aggressive setting. • DIM RED for a more aggressive setting.
6.
Release brake pedal.
Adjusting the Power to the Trailer Brakes
Once the control has been installed and properly leveled, it is necessary to set the power needed to stop the trailer during a braking event.
1.
Connect trailer to tow vehicle.
2.
Set Power Knob to the 12 o’clock position.
3.
Drive tow vehicle and trailer on a dry level paved surface at 25 mph and apply manual slide knob.
NOTE:
Range of adjustment for the level knob
from DIM ORANGE to DIM RED is 20 degrees of rotation.
✓
If trailer brakes lock up: ❑ Turn power down using power knob. (Rotate power knob toward the 8 o’clock position, counter-clockwise.)
✓
If braking was not sufficient: ❑ Turn power up using power knob. (Rotate power knob toward the 5 o’clock position, clockwise.)
4.
Repeat Step (3) until power has been set to a point just below wheel lock up or at a sufficient force as to achieve maximum braking power.
5.
Tekonsha 90885 Prodigy P2 Electronic Brake Control User Manual Tool
Using the brake pedal, make a few low speed stops to check the Power and Level adjust- ments. The automatic response (brake pedal) is initiated and terminated via the stoplight switch. When the brake pedal is released, trailer braking will cease.
Fine Tuning
Now that the Power has been set, it is time to fine tune the level setting for the majority of the stopping that you will be doing. 1.
Make several slow (25 MPH) stops as if coming up to a stop sign and take notice of how the trailer brakes respond:
✓
Brakes Grab Too Much ❑ You have an Aggressive Setting: To correct this condition rotate level knob clockwise, toward you, see below.
✓
Trailer Tending to Push Tow Vehicle ❑ You have a Delayed Setting: To correct this condition rotate level knob counter-clockwise, away from you, see below.
2.
Repeat until desired trailer braking is achieved.
A.
Delayed
B.
Normal
Prodigy P2 Brake Controller Reviews
C.
Aggressive
NOTE:
When the brake control is leveled
properly there will be very little current flowing through the brake magnets in a static state with the foot pedal depressed. The brake magnets will hum when there is current flowing through them. Anytime the Bi-Colored Light shows any color other than GREEN, there is current flowing through the brake magnets.
NOTE:
1. Front of the Voyager must be horizontal,
see below.
2. The Voyager must be parallel to direction
of travel, see below.
NOTE:
1.
WARNING This brake control is activated
by inertia and requires the level to be set properly, or the braking response will be too harsh or ineffective.
2.
To properly level the sensor, the trailer and tow vehicle must be parked on a level surface and trailer must be connected to tow vehicle.